PANDUIT: Electrical Full Line

For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory) ELECTRICAL SOLUTIONS E5.19 B2. Cable Accessories C1. Wiring Duct C3. Abrasion Protection C4. Cable Management D1. Terminals D2. Power Connectors E1. Labeling Systems E2. Labels E3. Pre-Printed & Write-On Markers F. Index B3. Stainless Steel Ties C2. Surface Raceway E5. Lockout/ Tagout & Safety Solutions B1. Cable Ties A. System Overview D3. Grounding Connectors E4. Permanent Identification Lockout/Tagout Safety Signs Indoor/Outdoor Sub-Surface Printed Adhesive Polyester (Type PPS) • High quality signs for use indoors and outdoors • Excellent resistance to UV light, chemical atmosphere, and abrasion • Excellent life and adhesion properties • Printed graphics are protected by clear polyester laminate Indoor/Outdoor Rigid Polyethylene (Type PRS) • Rugged signs for indoors and outdoors • Abrasion resistant • Used where adhesives will not work I ndoor Adhesive Vinyl (Type PVS) • Economical general purpose signs for use in most environments • Very good adhesive properties when applied to a clean, dry surface Material Chart Material Print Method Temperature Range Features Polyester (PPS) Pre-Printed -40°F to 275°F (-40°C to 135°C) Indoor/outdoor rated; laminated label material protects legend from abrasion and chemicals; resistant to UV light, chemical atmosphere, and abrasion; excellent life and adhesion properties. Rigid Polyethylene (PRS) -105°F to 250°F (-76°C to 121°C) Indoor/outdoor rated; high quality, rugged material resistant to abrasion; use where adhesives will not work. Vinyl (PVS) -40°F to 200°F (-40°C to 93°C) Indoor rated; economical general purpose material; excellent adhesion properties when applied to a clean, dry surface. WARNING LOCK OUT BEFORE SERVICING PVS0305W2102Y PVS0204C171Y PVS0204C176Y PVS0204C177Y HIGH VOLTAGE PPS0710D72 PRS0710D72 PRS1014D72 PVS0109D72Y PVS0204D72Y PVS0710D72Y PVS0204C178Y PVS0204C179Y PVS0204D100Y PVS0305C174Y PVS0505C174Y PPS0305C174 PVS0305W2101Y^ PVS0507W2101Y^ PVS0204W172Y PVS0209D445Y THE FOLLOWING STEPSMUST BEPERFORMEDWHEN LOCKING OUT EQUIPMENT: 1 - Identify all potential hazards and energy sources. 2 - Inform operator / supervisor about work to be performed. 3 - Prepare equipment for shutdown. 4 - Shutdown / turn offequipment. 5 - Isolate and LOCKOUT energy sources. 6 - Release all stored energy. 7 - Test equipment for zero energy state. 8 - Clear personnel / tools before and after job. 9 - Remove locks and tagswhenwork completed. PVS0503N458Y PRS1014B364 PVS0509B364Y PVS0710B364Y PPS0710B364 PRS0710B364 PVS0710C173Y PVS0710C180Y ^Can be clearly identified with Panduit permanent marking pens. *Denotes the part numbers’ prefix and suffix. Size Reference Chart Part Number Width Height Signs per Card In. mm In. mm *0109* 9 .00 228.60 1.50 38.10 1 *0204* 4.50 114.30 2.25 57.15 2 *0209* 9 .00 228.60 2.25 57.15 1 *0305* 5 .00 127.00 3.50 88.90 1 *0503* 3 .00 76.20 5.00 127.00 2 *0507* 7 .00 177.80 5.00 127 1 *0509* 9 .00 228.60 5.00 127 1 *0710* 10 .00 254.00 7.00 177.8 1 *1014* 14 .00 355.60 10.00 254 1 *0202* 2.25 57.15 2.25 57.15 4 *0505* 5 .00 127.00 5.00 127.00 1 PPS0202B493